Sensors

22Products found
  • OSF10-I0W

    LEVITON™ PIR Fixture Mount Integral Occupancy Sensor (120-277V)

    • Fixture Mount Integral Luminaire Occupancy Sensor lighting control, 120-277V.
    • Leviton’s OSF10, Integral Occupancy Sensor, is designed to be mounted directly into a luminaire.
    • The OSF10-I0W offers a sensor and relay in one device.
    • The wiring and housing of the sensor is installed adjacent to the ballast and hidden from view behind the reflector cover.
    • Only the PIR detector dome lens and locking ring are visible on the exterior of the fixture.
    • The OSF10-I0W uses Passive Infrared technology to detect motion.
    • For time delay, the time out occurs when motion is no longer detected by the sensor and the device counts a set amount of time before turning off the load.
    • If the device sensor detects motion during this ’time delay’ the count resets and the device initiates a new count.
    • The Time Delay can be adjusted to 30 seconds, 10, 20, and 30 minutes respectively.
    • Relay uses a zero-crossing circuitry to provide reliable, long-life operation.
    • A red LED blinks when motion is detected.
    • The Fresnel Lens detects small motion when mounted within 6 feet of occupants.
    • When mounted at a height of 8’, the coverage will be approximately 10’ diameter but sensitivity may be diminished.
    • Designed specifically for pre-wiring and installing inside of luminaire fixtures in small offices, cubicles, task lighting, cabinet lighting, and small bathroom lighting.

    SPEC SHEET | MORE FILES

  • OSFHU-ITW

    LEVITON™ PIR Fixture Mount Occupancy Sensor (120-347V)

    • High-Bay Fixture Mount Occupancy Sensor lighting control, Interchangeable Adjustable 360° Low Bay and (8′-20′), High Bay (20′-40′) Lenses, Aisle Mask, Passive Infrared Technology, 120/208/220/230/240/277/347V; 50/60Hz.
    • Quick-snap threaded nipple, Instant Start-up, Return-to-last state after power outage, Auto-Sensitivity gain from temperature increase, False-detection protection, Super Bright Green LED.
    • The OSFHU high-bay occupancy sensor is specifically designed for high mounted areas such as warehouses, manufacturing and other high ceiling applications.
    • It is a self-contained sensor and relay that turns individual light fixtures on or off based on occupancy in the detection zone.
    • It comes with three interchangeable lenses for use in either a 360-degrees high-bay or 360-degrees low-bay general area or an aisle way.
    • The OSFHU provides reliable coverage up to 40 ft. Mounting heights.
    • The OSFHU is also available in a model for cold storage applications with temperatures as low as -40°F. To improve the field-of-view for deep body fixtures, a separate offset adapter accessory (OSFOA-00W) can be used to position the sensor below the fixture body.
    • The adapter simply snaps into a 1/2-inch knockout on the end of the industrial fixture to attach the sensor.

    SPEC SHEET | MORE FILES

  • OSFHU-I4W

    LEVITON™ PIR Fixture Mount Occupancy Sensor (480V)

    • Fixture Mounted PIR Occupancy Sensor lighting control, Interchangeable Adjustable 360° Low Bay and High Bay Lenses and aisle mask, 480VAC, 50/60Hz, RF Immune
    • The OSFHU self-contained sensor mounts directly to a luminaire or electrical box to provide local occupancy control for either general area or aisle way pattern detection using PIR technology with a microprocessor based digital architecture that minimizes false triggering.
    • The OSFHU provides a trouble-free “install and forget” solution for high-bay lighting control.
    • The OSFHU high-bay occupancy sensor is specifically designed for high mounted areas such as warehouses, manufacturing and other high ceiling applications.
    • It is a self-contained sensor and relay that turns individual light fixtures on or off based on occupancy in the detection zone.
    • It comes with three interchangeable lenses for use in either a 360-Degree high-bay or 360-Degree low-bay general area or an aisle way.
    • The OSFHU provides reliable coverage up to 40 ft. mounting heights.
    • The OSFHU is also available in a model for cold storage applications with temperatures as low as -40°F. To improve the field-of-view for deep body fixtures, a separate offset adapter accessory (OSFOA-00W) can be used to position the sensor below the fixture body.
    • The adapter simply snaps into a 1/2” knockout on the end of the industrial fixture to attach the sensor. Green LED indicates occupancy detection.

    SPEC SHEET | MORE FILES

  • HB011-PDX

    LEVITON™ PIR Fixture Mount, Dimming Sensor with Daylight Harvesting (120-347V)

    • High Bay Fixture Mount Occupancy Sensor lighting control with Daylight Harvesting– PIR technology.
    • Single relay with one (1-10V sinking current) control line for use to connect directly to low voltage control ballast.
    • Fixture Mount Passive Infrared High /Low Bay Occupancy Sensor, Time Delay: 30 seconds to 30 minutes.
    • Includes Two (2) interchangeable, adjustable 360° lenses: High Bay Lens provides 1.5:1 spacing to mounting height coverage for 21 to 40 feet, and Low Bay Lens provides 2:1 spacing to mounting height coverage for 13 to 20 feet, 120-230-277 or 347V.
    • 1-100% continuous dimming control specifically designed for LED fixture control.
    • Suitable for use in standard and cold storage applications.
    • Visual RGB LED indicators for device status and troubleshooting.
    • Alternating relay software for increased lamp life.
    • Meets energy code requirements for ASHRAE 90.1 and Title 24 for electronic ballast loads 120/277V.

    SPEC SHEET | MORE FILES

  • OSFLA-ITW

    LEVITON™ PIR Fixture Mount Occupancy Sensor with Snap Lock Offset Adapter (120-347V)

    • lncludes an assembly of an OSFLO-W short length snap lock adaptor and an OSFHU-ITW, Quick Snap Connections
    • High-Bay Fixture Mount Occupancy Sensor lighting control, Interchangeable Adjustable 360° Low Bay and (8′-20′), High Bay (20′-40′) Lenses, Aisle Mask, Passive Infrared Technology, 120/208/220/230/240/277/347V; 50/60Hz.
    • Quick-snap threaded nipple, Instant Start-up, Return-to-last state after power outage, Auto-Sensitivity gain from temperature increase, False-detection protection, Super Bright Green LED.
    • The OSFHU high-bay occupancy sensor is specifically designed for high mounted areas such as warehouses, manufacturing and other high ceiling applications.
    • It is a self-contained sensor and relay that turns individual light fixtures on or off based on occupancy in the detection zone.
    • It comes with three interchangeable lenses for use in either a 360-degrees high-bay or 360-degrees low-bay general area or an aisle way.
    • The OSFHU provides reliable coverage up to 40 ft. Mounting heights.
    • The OSFHU is also available in a model for cold storage applications with temperatures as low as -40°F.
    • To improve the field-of-view for deep body fixtures, a separate offset adapter accessory (OSFOA-00W) can be used to position the sensor below the fixture body.
    • The adapter simply snaps into a 1/2-inch knockout on the end of the industrial fixture to attach the sensor.

    SPEC SHEET | MORE FILES

  • HB0LA-PDX

    LEVITON™ PIR Fixture Mount Dimming Sensor with Daylight Harvesting with Snap Lock Offset Adapter (120-347V)

    • Includes an assembly of an OSFLO-W short length snap lock adaptor and an HB011-PDX, High Bay Fixture Mount Occupancy Sensor lighting control with Daylight Harvesting PIR technology, Single relay with one (1-10VDC sinking current) control line for use to connect directly to low voltage control ballast.
    • Fixture Mount Passive Infrared High/Low Bay Occupancy Sensor, Time Delay: 30s-30m, (2) interchangeable, adjustable 360° lenses, the high bay PIR lens provides 1.5:1 spacing to mounting height coverage for 21-40 ft, the low bay lens provides 2:1 spacing to mounting height coverage for 13-20 ft, 120-230-277 or 347VAC
    • 1-100% continuous dimming control specifically designed for LED fixture control.
    • Suitable for use in standard and cold storage applications.
    • Visual RGB LED indicators for device status and troubleshooting.
    • Alternating relay software for increased lamp life.
    • Meets energy code requirements for ASHRAE 90.1 and Title 24 for electronic ballast loads 120/277V

    SPEC SHEET | MORE FILES

  • OSFLO-W

    LEVITON™ Snap-Lock Offset Adapter For OSHFU Sensor

    • Short length offset adapter for use with OSFHU occupancy sensors.
    • To improve the field-of-view for deep body fixtures, a separate offset adapter accessory (OSFOA-00W) can be used to position the sensor below the fixture body.
  • OSFHW-CTW

    LEVITON™ PIR Fixture Mount Occupancy Sensor for Wet Location and Outdoor LED High Bays (120-347V)

    • The OSFHW-CTW is a fixture mounted PIR LED High Bay Occupancy Sensor suitable for Wet Locations
    • Includes a 7.5 inch wire lead length and interchangeable adjustable 360 degree low-bay (8FT-20FT), and high-bay (20FT-40FT) lenses, blue, aisle mask.
    • Ideal for damp or wet locations such as supermarket meat departments, food processing plants, parking garages and other wash down, high ceiling applications.
    • The OSFHW features a IP65 rating for indoor and outdoor locations and is designed to withstand dust and pressure washers.
    • The sensor includes two interchangeable lenses for use in either a 360 degree High-Bay or 360 degree Low-Bay general area and includes an aisle mask accessory.

    SPEC SHEET | MORE FILES

  • BRI819P-B-O

    PIR On/Off Occupancy Sensor, Max Load 600W (120-277V), IP20 Dry Location, Available as an installed option.

    • Occupancy Sensor for CP, MCP Series LED Canopy Lights and VHO Series LED Vapor Tights.
  • BRI819P-B-D

    PIR Bi-Level Dimming and Daylight Harvesting Sensor, Max Load 600W (120-277V), IP20 Dry Location, Available as an installed option.

    • Bi-Level Dimming and Daylight Harvesting Sensor for CP, MCP Series LED Canopy Lights and VHO Series LED Vapor Tights.
  • BRI810-M-M8

    Installed PIR Photocell and Microwave Dimming Sensor

    • The BRI810-M-M8 sensor mounts has a slim, low-profile designed for installation inside the bottom of an LED luminaire’s body to provide multi-level control based on motion and/or daylight.
    • Its polycarbonate housing is flame retardant, UV resistant, and impact resistant.
    • It controls 0-1OV LED drivers, and is rated for wet and cold locations. All control parameters are adjustable using the RC-100 Remote Controller to store and transmit sensor profiles.
    • Provides line voltage On/Off switching and 0-1OV dimming control.
    • Time delay setting options from 5 to 30 minutes, with optional disable delay.
    • Adjustable ramp up and fade down times
    • Optional daylighting setpoints feature automatic calibration or manual adjustment.
    • Use optional RC100 Remote Controller Program to select and automate settings for brightness, sensitivity, hold time, standby-time, daylight sensor, and standby-dimming.
    • Suitable for commercial and industrial locations: parking, warehouses, gymnasiums, manufacturing, production, factories, gas stations, and pedestrian pathways.
  • BRI823

    Installed PIR Bi-Level Dimming Sensor with Photocell

    • The BRI823 sensor mounts has a slim, low-profile designed for installation inside the bottom of an LED luminaire’s body to provide multi-level control based on motion and/or daylight.
    • Its polycarbonate housing is flame retardant, UV resistant, and impact resistant.
    • It controls 0-1OV LED drivers, and is rated for wet and cold locations. All control parameters are adjustable using the RC-100 Remote Controller to store and transmit sensor profiles.
    • Includes two (2) PIR Lens for low bay (Low Mode) up to 25-FT, or high bay mounting heights (High Mode) up to 40-FT.
    • Provides line voltage On/Off switching and 0-1OV dimming control.
    • Time delay setting options from 5 to 30 minutes, with optional disable delay.
    • Adjustable ramp up and fade down times
    • Optional daylighting setpoints feature automatic calibration or manual adjustment.
    • Use optional RC100 Remote Controller Program to select and automate settings for brightness, sensitivity, hold time, standby-time, daylight sensor, and standby-dimming.
    • Suitable for commercial and industrial locations: parking, warehouses, gymnasiums, manufacturing, production, factories, gas stations, and pedestrian pathways.

Main Menu