-
HB011-PDX
LEVITON™ PIR Fixture Mount, Dimming Sensor with Daylight Harvesting (120-230-277-347V)
- High Bay Fixture Mount Occupancy Sensor lighting control with Daylight Harvesting– PIR technology, Single relay with one (1-10VDC sinking current) control line for use to connect directly to low voltage control ballast.
- Fixture Mount Passive Infrared High/Low Bay Occupancy Sensor, Time Delay: 30s-30m, includes two (2) interchangeable, adjustable 360° lenses, the high bay PIR lens provides 1.5:1 spacing to mounting height coverage for 21-40 ft, the low bay lens provides 2:1 spacing to mounting height coverage for 13-20 ft, 120-230-277 or 347VAC
- 1-100% continuous dimming control specifically designed for LED fixture control
- Suitable for use in standard and cold storage applications
- Visual RGB LED indicators for device status and troubleshooting
- Alternating relay software for increased lamp life
- Meets energy code requirements for ASHRAE 90.1 and Title 24 for electronic ballast loads 120/277V
-
HB0LA-PDX
LEVITON™ PIR Fixture Mount Dimming Sensor with Daylight Harvesting with Snap Lock Offset Adapter (120-230-277-347V)
- Includes an assembly of an OSFLO-W short length snap lock adaptor and an HB011-PDX, High Bay Fixture Mount Occupancy Sensor lighting control with Daylight Harvesting PIR technology, Single relay with one (1-10VDC sinking current) control line for use to connect directly to low voltage control ballast.
- Fixture Mount Passive Infrared High/Low Bay Occupancy Sensor, Time Delay: 30s-30m, (2) interchangeable, adjustable 360° lenses, the high bay PIR lens provides 1.5:1 spacing to mounting height coverage for 21-40 ft, the low bay lens provides 2:1 spacing to mounting height coverage for 13-20 ft, 120-230-277 or 347VAC
- 1-100% continuous dimming control specifically designed for LED fixture control.
- Suitable for use in standard and cold storage applications.
- Visual RGB LED indicators for device status and troubleshooting.
- Alternating relay software for increased lamp life.
- Meets energy code requirements for ASHRAE 90.1 and Title 24 for electronic ballast loads 120/277V
-
OSHFU-ITW
LEVITON™ PIR Fixture Mount Occupancy Sensor (120-347V)
- High-Bay Fixture Mount Occupancy Sensor lighting control, Interchangeable Adjustable 360° Low Bay and (8′-20′), High Bay (20′-40′) Lenses, Aisle Mask, Passive Infrared Technology, 120/208/220/230/240/277/347V; 50/60Hz.
- Quick-snap threaded nipple, Instant Start-up, Return-to-last state after power outage, Auto-Sensitivity gain from temperature increase, False-detection protection, Super Bright Green LED.
- The OSFHU high-bay occupancy sensor is specifically designed for high mounted areas such as warehouses, manufacturing and other high ceiling applications.
- It is a self-contained sensor and relay that turns individual light fixtures on or off based on occupancy in the detection zone.
- It comes with three interchangeable lenses for use in either a 360-degrees high-bay or 360-degrees low-bay general area or an aisle way.
- The OSFHU provides reliable coverage up to 40 ft. Mounting heights.
- The OSFHU is also available in a model for cold storage applications with temperatures as low as -40°F. To improve the field-of-view for deep body fixtures, a separate offset adapter accessory (OSFOA-00W) can be used to position the sensor below the fixture body.
- The adapter simply snaps into a 1/2-inch knockout on the end of the industrial fixture to attach the sensor.
-
OSFLA-ITW
LEVITON™ PIR Fixture Mount Occupancy Sensor with Snap Lock Offset Adapter (120-347V)
- lncludes an assembly of an OSFLO-W short length snap lock adaptor and an OSFHU-ITW, Quick Snap Connections
- High-Bay Fixture Mount Occupancy Sensor lighting control, Interchangeable Adjustable 360° Low Bay and (8′-20′), High Bay (20′-40′) Lenses, Aisle Mask, Passive Infrared Technology, 120/208/220/230/240/277/347V; 50/60Hz.
- Quick-snap threaded nipple, Instant Start-up, Return-to-last state after power outage, Auto-Sensitivity gain from temperature increase, False-detection protection, Super Bright Green LED.
- The OSFHU high-bay occupancy sensor is specifically designed for high mounted areas such as warehouses, manufacturing and other high ceiling applications.
- It is a self-contained sensor and relay that turns individual light fixtures on or off based on occupancy in the detection zone.
- It comes with three interchangeable lenses for use in either a 360-degrees high-bay or 360-degrees low-bay general area or an aisle way.
- The OSFHU provides reliable coverage up to 40 ft. Mounting heights.
- The OSFHU is also available in a model for cold storage applications with temperatures as low as -40°F. To improve the field-of-view for deep body fixtures, a separate offset adapter accessory (OSFOA-00W) can be used to position the sensor below the fixture body.
- The adapter simply snaps into a 1/2-inch knockout on the end of the industrial fixture to attach the sensor.
-
OSHFU-I4W
LEVITON™ PIR Fixture Mount Occupancy Sensor (480V)
- Fixture Mounted PIR Occupancy Sensor lighting control, Interchangeable Adjustable 360° Low Bay and High Bay Lenses and aisle mask, 480VAC, 50/60Hz, RF Immune
- The OSFHU self-contained sensor mounts directly to a luminaire or electrical box to provide local occupancy control for either general area or aisle way pattern detection using PIR technology with a microprocessor based digital architecture that minimizes false triggering.
- The OSFHU provides a trouble-free “install and forget” solution for high-bay lighting control. The OSFHU high-bay occupancy sensor is specifically designed for high mounted areas such as warehouses, manufacturing and other high ceiling applications.
- It is a self-contained sensor and relay that turns individual light fixtures on or off based on occupancy in the detection zone.
- It comes with three interchangeable lenses for use in either a 360-Degree high-bay or 360-Degree low-bay general area or an aisle way.
- The OSFHU provides reliable coverage up to 40 ft. mounting heights. The OSFHU is also available in a model for cold storage applications with temperatures as low as -40°F. To improve the field-of-view for deep body fixtures, a separate offset adapter accessory (OSFOA-00W) can be used to position the sensor below the fixture body.
- The adapter simply snaps into a 1/2” knockout on the end of the industrial fixture to attach the sensor. Green LED indicates occupancy detection.
-
OSFLO-W
LEVITON™ Snap-Lock Offset Adapter For OSHFU Sensor
- Short length offset adapter for use with OSFHU occupancy sensors.
-
OSF10-I0W
LEVITON™ PIR Fixture Mount Integral Occupancy Sensor (120-277V)
- Fixture Mount Integral Luminaire Occupancy Sensor lighting control, 120-277V.
- Leviton’s OSF10, Integral Occupancy Sensor, is designed to be mounted directly into a luminaire. The OSF10-I0W offers a sensor and relay in one device.
- The wiring and housing of the sensor is installed adjacent to the ballast and hidden from view behind the reflector cover.
- Only the PIR detector dome lens and locking ring are visible on the exterior of the fixture.
- The OSF10-I0W uses Passive Infrared technology to detect motion.
- For time delay, the time out occurs when motion is no longer detected by the sensor and the device counts a set amount of time before turning off the load. If the device sensor detects motion during this ’time delay’ the count resets and the device initiates a new count. The Time Delay can be adjusted to 30 seconds, 10, 20, and 30 minutes respectively.
- Relay uses a zero-crossing circuitry to provide reliable, long-life operation.
- A red LED blinks when motion is detected.
- The Fresnel Lens detects small motion when mounted within 6’ of occupants. When mounted at a height of 8’, the coverage will be approximately 10’ diameter but sensitivity may be diminished. The field-of-view below shows maximum coverage.
- Designed specifically for pre-wiring and installing inside of luminaire fixtures in small offices, cubicles, task lighting, cabinet lighting, and small bathroom lighting.
-
IP710-LFZ
LEVITON™ 0-10V Wired Slide Dimmer (120-277V)
- IllumaTech Slide Preset NAFTA Compliant Electro-Mechanical 0-10V Slide Dimmer for use with LED Power Supplies
- Suitable for use with Class 1 or Class 2 wiring, 1200VA @ 120VAC, 1500VA @ 277VAC, 10A LED/Electronic Ballast 120/277VAC, 60Hz, 50mAmps maximum sinking current
- Single pole or 3-way control when used with 3-way switch
- No power pack required for switching
- Dual voltage 120V/277V; 50mAmps maximum sink current
- Provides single pole or 3-way lighting control when used with a 3-way switch (sold separately)
- Compatible with Decora Plus™ screwless and Decora standard designer wallplates (sold separately)
- Fluid slide movement allows fine adjustment of light level with minimal effort
- Wallplate order separately
-
BRI819P-B-O
PIR On/Off Occupancy Sensor, Max Load 600W (120-277V), IP20 Dry Location, Available as an installed option.
- Occupancy Sensor for CP, MCP Series LED Canopy Lights and VHO Series LED Vapor Tights.
-
BRI819P-B-D
PIR Bi-Level Dimming and Daylight Harvesting Sensor, Max Load 600W (120-277V), IP20 Dry Location, Available as an installed option.
- Bi-Level Dimming and Daylight Harvesting Sensor for CP, MCP Series LED Canopy Lights and VHO Series LED Vapor Tights.
-
BRI823
Installed PIR Bi-Level Dimming Sensor with Photocell
- The BRI823 sensor mounts has a slim, low-profile designed for installation inside the bottom of an LED luminaire’s body to provide multi-level control based on motion and/or daylight contribution.
- Its polycarbonate housing is flame retardant, UV resistant, and impact resistant.
- It controls 0-1OV LED drivers, and is rated for wet and cold locations. All control parameters are adjustable using the RC-100 Remote Controller to store and transmit sensor profiles.
- Includes two (2) PIR Lens for low bay (Low Mode) up to 25-FT, or high bay mounting heights (High Mode) up to 40-FT.
- Provides line voltage On/Off switching and 0-1OV dimming control.
- Time delay setting options from 5 to 30 minutes, with optional disable delay.
- Adjustable ramp up and fade down times
- Optional daylighting setpoints feature automatic calibration or manual adjustment.
- Use optional RC100 Remote Controller Program to select and automate settings for brightness, sensitivity, hold time, standy-by-time, daylight sensor, and stand-by-dimming.
- Suitable for commercial and industrial locations: parking, warehouses, gymnasiums, manufacturing, production, factories, gas stations, and pedestrian pathways.
.
-
RC-100 Remote
Remote Controller to Program BRI823 Sensor
- The RC100 Remote Controller can store up to four (4) sensor parameter modes to speed configuration of multiple BRI823 Sensors installed in luminaires.
- It uses bidirectional infrared communication to send and receive sensor settings with a maximum mounting height of 50 feet.
- The device can display previously established sensor parameters, copy parameters and send new parameters, or store parameter profiles.
- For projects where identical settings may be desired across a large number of areas or spaces, this capability provides a streamlined method of configuration. Settings can be copied throughout a site, or in different sites.
- Program and automate settings for brightness, sensitivity, hold time, standy-by-time, daylight sensor, and stand-by-dimming.
- Uses two (2) AAA 1.5V alkaline batteries.
Applications
- LED Area Lights
- LED Bollards
- LED Canopy Lights
- LED Down Lights
- LED Dusk to Dawn Lights
- LED Flood Lights
- LED Gas Station Lights
- LED Grow Lights
- LED High Bays
- LED Lamps & Replacements
- LED Low Bays
- LED Panels
- LED Post Top Lights
- LED Retrofits
- LED Stadium Lights
- LED Street Lights /Cobraheads
- LED Troffers
- LED Vapor Tights
- LED Wall Packs
- LED Wraparounds